|
bed
|
86 nissan 720
|
83 720
|
use the 86 tail lights and tailgate
|
|
rottweilersam
|
|
|
6 Lug 5.5 Bolt Pattern
|
All Makes & Models of Trucks
|
Nissan 720
|
offsets from front to back must be checked or cut in two
|
Toyota rims
|
86_720_Nissan
|
|
|
6 Lug to 5 Lug (114.5mm/4.5") Conversion (front only! Use Toyota rear axle for the back)
|
89 to 95 Toyota Pickup (2wd)
|
83 to 97 Nissan Pickup
|
Nation Federal Mogul (Moog) Hub Seals Part #710175 (it's an inner oil seal, you may want to shim your brake calipers 1 or 2mm to center them on the rotors, otherwise it's a perfect fit)
|
None. P.S. you can check out the full swap with pics here: http://www.nissanminis.com/modshop.php?mod_cat=9 (link broken TTR)
|
aaronraven
|
|
|
Any 5 spd gearbox
|
720 4x2 & 4x4
|
720 4x2 & 4x4
|
use original bell housing
|
possible length difference in rear extension housing. Mod Tail shaft to suit
|
Aussie_720
|
|
|
any 6 hole wheels
|
full size chevy/gmc 4x4
|
nissan 720 4x2
|
none
|
none
|
lee
|
|
|
Bucket Seats
|
88-91 Honda CRX
|
720 4x4 k/c or 2wd should work on reg cab
|
rear mounting tabs must be cut off stock units and rewelded on to donors
|
Not sure if this will work on reg, otherwise easy swap...as easy as swapping wives..hahaha
|
NIS-720
|
|
|
Bucket Seats
|
1981 Datsun 280ZX
|
1981 Datsun Pickup (probably 82-85 also)
|
none mecessary
|
|
ajwj34
|
|
|
Bucket Seats
|
early 90's Mazda 626
|
720 xcab
|
tear down original seat and use the frame and sliders to weld onto mazda seat. Remove mazda seat sliders.
|
|
comandolb@hotmail.com
|
|
|
Cast aluminum valve cover
|
1982-83 200SX or Z22 Truck
|
All 720s with a Z24 engine
|
Longer bolts and the 200SX cover gasket
|
None
|
moxman
|
|
|
Distributor
|
Z24i/KA24
|
Z20/22/24
|
need Z24i or KA24 oil drive shaft/gears
|
Will work only with aftermarket ignition (crank trigger)
|
TTR
|
|
|
Drum brake bleeder valve
|
90 Nissan Pathfinder
|
82-85 2wd 720
|
None - (same)
|
4WD may be different
|
84LongRunner
|
|
|
EGR Tube
|
1978-1988 Nissan 200SX
|
720 w/ z24 engine
|
Take it to a pipe shop and have them cut the female end off about 2" and reflange - Available from www.oem-surplus.com
|
Make sure you have your old EGR tube or the EGR valve end to match the length and bend
|
CrumTheBum
|
|
|
Factory Carburetor
|
L16-Z22
|
L16-Z22
|
just use the original linkage
|
Z24 is different
|
BigJim
|
|
|
Fiberglass (and probably also alum. and steel) bed cover, cap, canopy or whatever you call it in your neck of the woods
|
early Ford Ranger pick up with the same bed length, not the long bed model
|
1985 KK
|
none
|
there are slight differences in the angles of the rear of the 2 trucks cabs, but this can be compensated for by using any of the different style of several inch thick, flexible type of cab to cap connectors
|
goodolboydws@bellsouth.net
|
|
|
Hi volume oil pump
|
Z24i or KA24E (RWD only) D-21/240sx/Pathfinder
|
any L series and all Z series 720 trucks
|
none just fill with oil
|
none
|
datzenmike
|
