A - LUCKY LOANS

COMPUTER PRINTER REFILL INK

REFILL AND RECYCLE YOUR OWN CARTRIDGES. WHEN YOU RUN OUT OF INK, JUST INJECT INK INTO THE CARTRIDGE AND YOU ARE PRINTING AGAIN IN MINUTES.

IT IS QUITE SIMPLE AND
I WILL SHOW YOU HOW.
MOST CARTRIDGES (WE FILL) FOR $10.00 OR LESS.

IF YOU FORGET HOW, GIVE ME A CALL OR COME IN, AND I WILL REFRESH YOUR MEMORY BY SHOWING YOU THE PROCEDURE STEP BY STEP.

THE CORRECT INK IS AVAILABLE FOR ALMOST ALL INKJET CARTRIDGES. I STOCK APPROXIMATELY 25 COLORS OF EACH COLOR, (CYAN, MAGENTA, YELLOW, & BLACK).

SOME CARTRIDGES CAN BE REFILLED FOR AS LITTLE AS $.50 IF YOU DO IT YOURSELF.

LETS SAY YOU PURCHASED A KIT SOMEWHERE ELSE. BRING IT IN AND WE WILL SHOW YOU HOW TO USE IT THE CORRECT WAY. THOSE DIRECTIOINS ARE SO DARN CONFUSING ARENT THEY?

MAINTENANCE

IT IS BEST TO REFILL THE CARTRIDGE AS SOON AS YOU NOTICE THE INK IS FADING. IF IT IS NOT DONE AT THIS TIME YOU MAY OR MAY NOT BE ABLE TO REVIVE AND RECYCLE THE CARTRIDGE. YOU WILL BE SHOWN HOW TO REFILL THE CARTRIDGE, SO BRING YOUR CARTRIDGE WITH YOU THE FIRST TIME YOU PURCHASE INK.

IF YOU ALREADY PURCHASED INK AND YOUR CARTRIDGE WILL NOT PRINT YOU MAY NEED TO SOAK THE PRINT HEAD OR BLOW IN THE TOP TO FORCE THE INK OUT THE PRINT HEAD

TO SOAK THE PRINT HEAD: PUT 1/4 INCH OR WATER IN A MICROWAVE SAFE CUP, HEAT IN THE MICROWAVE ON HIGH FOR 1 MINUTE, (CAUTION: IT WILL BE VERY HOT). PUT THE CARTRIDGE PRINTHEAD INTO THE WATER, LET STAND FOR APPROX 1 MINUTE OR UNTILL IN FLOWS FROM PRINTHEAD. TEST BY DOBBING ON FOLDED PAPER TOWEL, DO NOT WIPE THE PRINT HEAD, YOU MAY GET PAPER FIBERS IN THE PRINT HEAD HOLES, WHICH WILL THEN NEED TO BE SOAKED AGAIN OR RUN YOUR PRINTERS PRINTHEAD CLEANING CYCLE.
ANY QUESTIONS CONTACT ME ON MY MESSAGE BOARD OR E - MAIL ME AT rmmwatch@hotmail.com.

HP 51626A/G, 51629A/G & C6614AN

SNAP & FILLILL

Supplies you should have before you begin: Paper towel, latex gloves because ink can and does make a mess plan for this before you begin filling cartridges. You may want to fill them initially in a sink as you gain experience using the Snap & Fill.

1. A freshly emptied cartridge works best. If the cartridge has been out of the printer awhile, you may need to unclog the dried ink from the nozzles before the cartridge will accept the full amount of ink. Do this by heating about 1/4 inch of water in the microwave for about 1 minute, then put the print head of the cartridge in it. You may have to repeat this step until you get the printhead clean. Remember only daub the printhead on the paper towel do not wipe over the print head. Snap the cartridge into the filling device. Make sure the cartridge is centered in the device by feeling both sides.

2. Using the syringe ink tip provided draw 30cc of ink from the bottle into the syringe.

3. You may want to do this procedure over a sink the first few times just in case it makes a mess. The process is actually pretty clean, but let your confidence build. Push the end of the syringe onto the plastic tube. Hold the cartridge and syringe as shown and slowly inject the ink, taking about 5 seconds to completely empty syringe.

4. This last step is important. In order to keep the ink from leaking, a little vacuum is needed inside the cartridge. On top of the cartridge there is an arrow with a small hole in the middle, blow air into this hole. (This will force ink out the printhead. So you may want to do this step over a paper towel.) Allow the cartridge to sit for a while, this will ensure the cartridge is not leaking.

5. The cartridge is now ready to be used.

A - LUCKY LOANS

JEWELRY SALES

WATCH REPAIR

NEED INTERNET SERVICE AT A PRICE YOU CAN AFFORD TRY THIS SERVICE I USE IT. www.lightspeedbroadband.net